Home > OTHER CALIBERS > 9mm >

New Frontier 80% AR-15 Lower Completion Jig
New Frontier 80% AR-15 Lower Completion Jig


 
Sale Price $65.00
SALE PRICE: $62.00
Savings: $3.00
 

Stock Status :(Out of Stock)
Product Code: 80JIG01

PLEASE ACKNOWLEDGE

I AFFIRM THAT I AM OF LEGAL AGE AND ELIGIBLE UNDER THE LAWS OF MY STATE OF RESIDENCE AND FEDERAL LAW TO PURCHASE, OWN, AND USE THE COMPONENTS CONTAINED IN MY ORDER.

Qty:  
Description
 

New Frontier Armory 80% AR-15 Lower Completion Jig

The New Frontier Armory 80% AR-15 Lower Completion Jig is all you need to complete the final machining process to turn your 80% AR-15 Receiver into a working stripped lower receiver. This jig works with our C-4, C-9 (9mm), C-45, C-10, and G-15 80% Lowers and all other 80% lowers on the market! Proudly made in the USA by hardworking American men and women.

Includes:

  • Instructions to complete using a drill press
  • Instructions to complete using a milling machine
  • Left and Right side fixture plates / vice jaws
  • Three top plate templates
  • All hardware necessary to secure jig and top plate

Please note: Some states may not allow you to legally manufacture a firearm without a serial number (like the state of NJ and Washington DC). Please be sure to do your due diligence and make sure you are following your state and local laws before attempting to manufacture a firearm. This is not intended and should not be construed as an advertisement or offer for sale of any of our products to New Jersey or Washington DC residents or any person in New Jersey or Washington DC.

Average Rating: Average Rating: 2 of 5 2 of 5 Total Reviews: 4 Write a review »

  1 of 1 people found the following review helpful:
 
1 of 5 not good November 3, 2019
Reviewer: paul karg from bensenville il  
Used once and not again,  Made a mess out of the lower walls to thin and burn through in the mag release  hole drilling is bad , top plate holes not  now i need to buy a different jig don't trust this one at all

Was this review helpful to you?

  2 of 2 people found the following review helpful:
 
1 of 5 horid August 27, 2019
Reviewer: jay rollins from muncie, IN United States  
the kit SAYS you can finish with just a drill press or MILL/ROUTER but the top plate has four bolts on top that make it IMPOSSIBLE to get a flush surface to use router. so i used the DRILL PRESS OPTION which SUCKS SAYS drill a bunch of tiny holes then use those holes as guide for bigger bit that is supposed to cut out majority of  alluminum the only problem is  once you drill into one of the smaller holes it cuts halfway or MORE into the next guid hole which makes it IMPOSSIBLE to keep a drill bit on without it kicking off to the side thats already cut! also there is only a SAFETY SELECTOR HOLE ON ONE SIDE!!! AND NEVER TELLS YOU TO DRILL ALL THE WAY THROUGH! BY FAR WORST INSTRUCTIONS IV EVER HAD ON A PRODUCT AND THE PROCESS DOES NOT WORK AS ADVERTISED! DONT BUY

Was this review helpful to you?

  0 of 1 people found the following review helpful:
 
4 of 5 AR15 lower jig March 27, 2017
Reviewer: Wallace Hamilton from Gulfport, MS United States  
Right to Bear Arms is one of the best companies I have ever done business with. Quick to respond to questions, great pricing and lightening fast at shipping your item! I would recommend them to anyone! The jig is good but if the holes on the top plate were bigger it would reduce drill time and make it easier to get a nice finished product. All in all though I was satisfied with it.

Was this review helpful to you?

  7 of 8 people found the following review helpful:
 
1 of 5 Inaccurate March 12, 2017
Reviewer: Joshua Wilson from Iva, SC United States  
I used the jig on two lowers and both safety holes are off center with detent hole. I do NOT recommend this product

Was this review helpful to you?


Browse for more products in the same category as this item:

OTHER CALIBERS > 9mm
AR15 Parts > 80% Lower Receivers
AR15 Parts > 80% Lower Receivers > JIGS & TOOLS